Wismec Ravage 230 intro
Wismec and Sinuous are returned at it once more. The Ravage 230 functions a large the front-facing color display and places out 230 watts of strength from two 18650 batteries (now not blanketed). Packed with functions like TC and pre-heat settings all in a small form component much like the Predator, it aims to be the mod the Predator ought to had been, if no longer for the 510 problems.
This overview may be focused across the overall performance test consequences. If you’re no longer involved, soar to professionals and cons and the decision. But if you’re curious if the Ravage 230W does come thru with its guarantees… read directly to discover.
Colors: Red, custom blue, brushed stainless and excessive-gloss black
Initial impressions and features
When I first were given this mod, it jogged my memory a lot of an updated Predator. It has the same form issue and aesthetics, proper all the way down to the fire bar. There were some minor updates to the layout however. This time round they went with a complete-shade display. They additionally targeted the 510-pin to be able to allow up to a 28 mm atomizer to take a seat flush on it.
The menu has been up to date into some thing a whole lot higher and extra user friendly than the older Wismec mods. They’ve additionally delivered in another button above the fire bar that may be used to turn the display screen on and off, or to cycle thru modes with out entering the menu. Also, the paint task on it’s miles amazing. It nearly looks as if it were anodized, but it’s no longer. No scratching or peeling in any respect.
Testing historical past
I check all mods the usage of an oscilloscope to find out exactly how correct and steady the mod itself is. All checking out is performed the usage of completely-charged Sony VTC5a batteries (above four.Zero V per cellular). This is finished in a controlled testing surroundings and I’m aware about the dangers involved and make appropriate precautions. I don’t recommend vaping over 150 watts on a dual battery mod. Always use real 20-Amp CDR or better batteries together with Sony VTC6, VTC5a, or Samsung 30Q.
I ran exams at resistances of zero.Eleven ohms, 0.15 ohms, zero.2 ohms, and zero.49 ohms.
The lowest resistance of 0.11 ohms allows me to test the max amperage of the mod. It capped out at forty four amps which is superb for a twin-battery mod. Anything higher than forty is above average. That’s a max output of 213 watts with a 0.11-ohm coil, which could be very mind-blowing for a dual-battery mod. Outside of that, at 0.11 ohms, the mod hits anywhere from 1-14 watts lower than the actual placing. It’s plenty more accurate beneath a hundred watts. This is ordinary behavior for maximum dual-battery mods at this resistance
Most dual-battery mods attain their max wattage inside the zero.14 to 0.2-ohm resistance range.
For my take a look at at zero.15 ohms, the mod maxed out at 231 watts, meeting its promised specs. It’s also extremely correct at this resistance; it’s by no means being off via more than one watt, which may be very astonishing.
At 0.2 ohms, it maxed out at 234 watts, hitting its max wattage. At 200 watts it turned into 6 watts higher, but under 200 watts it was by no means off by using extra than 2 watts. Again, an terrific performance for a twin battery mod and plenty higher than most.
Next, I did a high resistance check of 0.49 ohms to locate the max voltage output of the mod.
The Wismec chip truly has its limits built into the firmware and gained’t will let you adjust past that. So, at a 0.Forty nine-ohm resistance, the max placing of the mod is capped at one hundred sixty five.Three watts because of the nine-volt max. Output at this putting was 171 watts that is nine.152 volts, meeting its nine-volt stated restrict and shows that the mod does have a boost circuit that’s a pleasant plus. Many mods are greenback simplest, however we’re seeing more and more mods popping out with a lift circuit which facilitates performance at higher resistances. As a long way as accuracy goes, the mod does hit higher than expected at this resistance. At one hundred watts or more, it’s 6 to thirteen watts higher than the setting. Under one hundred watts it best hits 1-6 watts higher. This is standard for most twin battery mods.
All in all, they list the specs as 50 amps, 230 watts and 9 volts max output. In my check results the wattage and voltage output were met and exceeded through a little, making it an as it should be-rated tool. The amp output fell a bit quick at forty four amps, however nevertheless puts it at above common for a dual-battery mod.
The output became smooth and consistent in my checking out and the mod doesn’t get warm, only heat at definitely high wattages. Nothing to be involved approximately. Overall, I locate this to be an top notch performer that is properly above average for a twin-battery mod.
Temperature control performance
Using SS316 wire with the default SS mode I tested 8 builds starting from round spaced to special single and twin coil builds. Overall, I became pretty inspired with the performance at the fee factor of this mod. In 2017, we’ve visible a number of suitable-appearing temp manipulate mods that don’t value an arm and a leg. The Wismec Ravage 230 is proper there with them. It’s been easy, steady and has notable ramp up instances. And there’s no limit on energy in temp manage except the mod’s max wattage. It throttles again properly and is in no way “pulsey” or absolutely off.
I like a heat vape and each build I’ve used has labored properly inside the 450-470 F variety so it feels quite accurate, with desirable dry hit safety. I did have one instance after a battery trade wherein it hit truely hot, then kicked me lower back to electricity mode. This best occurred one time so I’m inclined to chalk it up as a fluke, however I felt it become really worth bringing up. All the opposite instances, no trouble at all. I think most will locate their desired vape in the four hundred to 480 F variety which is the way it ought to be. Overall, I found the Ravage 230 to be a stable performer in temp control mode.
Other utilization information and features
The Mod itself can only be disassembled a lot. It’s impossible to see the internal make-up of the 510-pin, but I’ve used over a dozen atomizers consisting of SMOK tanks in this mod with out a troubles. I’ve additionally pulled on the 510 and wiggled it however noticed no troubles or drop in overall performance like I even have with other Wismec mods. Nothing in my testing has shown any problems both. For all intents and functions, I’ve determined no troubles with the 510 pin that’s a first from a Wismec product for me.
The colour display screen on the Ravage 230 is big, shiny and offers you all of the data you’ll ever need or need. It has a digital clock and a puff counter as properly.
The Ravage additionally has a pre-heat function that allows you to choose the wattage and the duration of the preheat.
The battery door works properly and is straightforward to open and near with no gaps.
The targeted 510 pin permits for up to a 28 mm atomizer without overhang.
The mod capabilities a firing bar so that you can just squeeze it to fireplace. It works nicely and is quality and clicky.
The mod does characteristic 2-amp speedy charging, but I in no way advise charging more than one battery mods internally, so I didn’t test that out. Always use an outside charger.
How to use the Ravage 230
The mod follows the same old five clicks to show on and rancid. It has an additional button on top of the hearth bar. This button does 2 matters. Click it to show the display screen on or off or hold it to cycle through modes. Personally, I don’t use it as I find it quicker to use the normal menu system. To enter the menu, use three clicks. This brings you to a sub menu for mode, settings, info and go out to go back to the principle display. Use the up and down buttons on the front to scroll and the hearth bar to lock in your choice.
Going into Modes offers you power, temp control, real time clock (RTC), and TCR. Temp manipulate has defaults for Ni200, Ti, and SS316 cord. In settings, you may lock your coil, alternate the power in TC mode, input the Subpara menu, set your pre-warmth, clock, and your display timeout.
In the Subpara menu, it shows your puff counter, puff timer and has an alternative for amp which does not seem to do anything. In the information menu you can see your man or woman battery voltages and your firmware and hardware versions.